A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
Listed here below you will discover a lot of reliable help and advice relating to A Step-by-Step Guide to Installing a Bathtub.
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and often, tiling abilities. Changing an old bathtub with a new one is also a moderately hard job. If the old bathtub is readily obtainable, the project can relocate speedily; if you have to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the task is much harder. In either instance, the task is within a home handyman's skills, although you will certainly require an assistant to move out the old bathtub and also set in the brand-new one. Make sure you have actually certified on your own for the task and also fit attempting it. As opposed to employing a service provider to take control of a halfway-completed project, it is better to think about using one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you mount a brand-new bathtub in your restroom if you have currently gotten a new bathtub as well as do not require to change the plan of your previous water supply pipes.
Your tools and also product checklist ought to make up the following:
Planning for the Setup
First of all, the sustaining structure provided with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make sure that if the tap includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you use every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be suited its last position.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is separate the water supply. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The process of getting rid of the existing faucets can be quite bothersome because of the limited gain access to that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the remaining water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Making use of both wood boards under its feet, position the bath tub in the required setting. The wooden boards are handy in equally spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 tiny points.
The next objective is to make sure that the tub is leveled all round. This can be achieved by examining the level and readjusting the feet on the tub until the level reads degree.
To install faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipe by making a compression join; after that do the same for the other faucet.
Activate the water supply as well as check all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise check the overflow electrical outlet as well as the typical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as securing around the bathtub needs to wait until the bath tub has actually been made use of a minimum of when as this will certainly resolve it right into its last position.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making certain that the washing machines remain in area in between the faucet and also the sink. Secure the tap in position with the manufacturer provided backnut. Once the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular tap connectors. The former kind must be linked to the tap finishes initially, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to split a rigid seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, resulting in difficulties with moisture and feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, and can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill the tub with water prior to securing, to permit the activity experienced when the bathtub remains in use. The sealant can break relatively early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently readily available on the market. It is recommended to fit the floor tiles utilizing water-resistant or waterproof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed our part on Installing A Bathtub. Thank you for spending some time to browse our piece. Kindly take the opportunity to promote this write-up if you enjoyed reading it. I am grateful for your time. Kindly pay a visit to our blog back soon.
Customer Reviews Report this page